Masonry Saws, brick saws, block saws, concrete saws, stone saws, chain saws, cut off saws, bridge saws, rail saws, wet saws, hand held saws, walk behind concrete saws
HomeNew VendorsPrivacy PolicyCredit ApplicationContact Us
Tile saws, wet saws, ceramic tile saws, table saws, tile cutters, tile cutting saw, ceramic tile cutters Masonry Saws, brick saws, block saws, concrete saws, stone saws, chain saws, cut off saws, bridge saws, rail saws, wet saws Core drill, diamond core drill, concrete core drill, core drill dry, core drill rig Saw Blades, diamond blades, metal blade, stone blades, diamond saw blades, circular saw blade, concrete saw blades, band saw blades, diamond chains
 ph. 1-800-593-6095
  CORE CUT | FELKER | HUSQVARNA | ICS | IMER | MK DIAMOND | NED-KUT | PARTNER | PRO-CUT | QEP | TARGET  
FREE SHIPPING - On orders over $300 - Applies to UPS Ground Only (No Common Carrier) - Click here for details

 
CHAINSAWS PRODUCT LIST  |  GUIDE BARS  |  DIAMOND CHAINS  |  ACCESSORIES  |  KEY REPLACEMENT | FAQ

613GC CUT-OFF CHAINSAW
The ICS 613GC ChainSaw

The 613GC from ICS cuts twice the depth of an ordinary circular blade cut-off saw.

Weighing only 21 pounds complete, this new saw is capable of plunge cutting to twelve inches and will cut a square opening with no over-cuts in material as thick as ten inches.

The 613GC is powered by an 80cc, 5.7hp, 2-cycle gas engine, with an advanced air filtration system designed for wet-cutting aggregate materials.

Whether your need is for remodeling, new
construction, construction repair or controlled demolition, the 613GC is designed to handle the wide range of concrete and masonry cutting requirements encountered on the job.

613GC Chainsaw Datasheet - (.pdf format) Requires Adobe Acrobat Reader to view
613GC Operator Manual - (.pdf format)
Bar Dimension and Cutting Depths Chart - (.pdf format)

Features:
• Long lasting "rim-style" drive sprocket
• Reliability features built-in to eliminate minor breakdowns:
- Air filter water seal system
- High strength, electroplated chain tensioning screw
- Pre-lubricated starter pawls
- No kink water inlet hose
• Uses Diamond Chains with SealPro® O-Ring technology
• Use the 613GC with standard "garden hose" water pressure. No need for a water booster pump.
• 5.7hp (80cc) engine designed specifically for wet cutting concrete in an abrasive environment
• Special crankshaft sealing and air filtration
• Sprocket side cover and guard flap designed for maximum operator safety
• Easy access and simple maintenance requirements
• Fixed-Position WallWalker® helps ensure easier cuts in multiple positions

Specifications
Engine Type
  • 2-stroke Air Cooled Single Cylinder
    		•
    Displacement
  • 4.9 cu. inch (80 cc)
    • Horsepower
  • 5.7 HP (4.2 kw) @ 9,000 RPM
    • Torque
  • 37.2 in-lbs. (4.2 N-m)
    • Engine Speed
  • 12,000 ± 500 RPM, electronically governed
  • 2,800 – 3,200 RPM idle
    • Chain Speed
  • 5,300 sfm (27 m/s), free running
  • 4,000 sfm (20 m/s), in the cut
    • Weight
  • 21 lbs (9.5 kg) with bar and chain
    • Cutting Depth
  • Up to 12 inches (30.5 cm)
  • 10 inches square (25.4 cm)
    • Dimensions
  • 18 inches (46 cm) Length
  • 11.5 inches (29 cm) Height
  • 10 inches (25 cm) Width
    • Air Filter
  • Dry nylon
  • No oil required
  • Washable
    • Carburetor
  • Walbro WJ85A
  • Throttle shaft sealed
  • Pressure compensating
    • Starter
  • Dust and water shielded
    • Ignition
  • Special water resistant electronic ignition
    • Clutch
  • Three-weight, single-spring
    • Fuel Mix Ratio
  • 50:1 gasoline-to-oil
    • Fuel Capacity
  • 0.23 gal (.88 liters)
  • 15 – 18 minutes runtime per tank, continuous full-load operation
    • Water Supply
  • Minimum 20 psi (1.5 bar)
    • Noise Level
  • 100 dB @ 1 meter
    • Vibration Level
  • 10.5 m/s2 (front handle)
    • Cutting Rate
  • Hard aggregates w/steel: 15-25 sq-in/min
    (90-160 sq-cm/min)
    Medium aggregates: 20-30 sq-in/min
    (160-190 sq-cm/min)
  • Masonry, soft aggregates: 30-50 sq-in/min
    (190-320 sq-cm/min)
    • 613GC GAS CHAINSAW
    PART # DESCRIPTION LIST PRICE YOUR PRICE SHIP ME
    ICS71995 613GC-12 Chainsaw Package
    (Includes 12-Inch Guide Bar and TWINMAX-29 Diamond Chain)    		 $1495.00 $1120.00
    ICS514268 613GC-14 Chainsaw Package
    (Includes 14-Inch Guide Bar and TWINMAX-32 Diamond Chain)    		 $1595.00 $1195.00
    ACCESSORIES
    ICS70708 Hard Carrying Case - Fits 613GC $176.00

    Call for special pricing

    ACCESSORIES
    613GC Diamond Chain & Bar
    TwinMax™ Chain
    • 29 Diamond Segments - high diamond concentration and quality for long life
    • Uses SealPro® Technology
    • Multipurpose - cuts reinforced concrete, brick, block and natural stone
    • Cuts fast - 5 minutes through 6 inches (15 cm) thick for 2 feet (.6 m) distance
    • More About Diamond Chains

    Order On-Line
    SealPro® Technology incorporates a patented chain chassis design that seals out the abrasive contaminants present in the concrete cutting environment. A unique o-ring design seals the rivet-joints of the chain, keeping the abrasive materials out and the lubrications in. 20 psi (1.4 bar) minimum water pressure required.

    12" Bar

    • 12" Penetration, 10" square cuts
    • Water passes through core of bar to clean out slurry and reduce chain wear
    • Reversible for long life
    • More about Guidebars

    Order On-Line

    613GC Accessories

    613GC Case

    • Custom 613GC carrying case
    • Continuous piano hinge
    • Tough 3/16-inch ABS plastic

    ICS 2-stroke oil

    • Proprietary blend for ICS gas saws
    • Specially formulated for heavy load cycle
    • Improved thermal stability
    • 2.6 oz bottles are available in 6-packs or by the case (24-pack)
    • One 2.6 oz bottle of ICS 2-stroke oil in one gallon of gas makes the 50:1 mix recommended for the best performance from your 613GC cut-off saw.
    • One bottle of ICS 2-stroke oil comes with each 613GC package (p/n 70705 & 70700)
    • Oil Datasheet - (.pdf format) requires Adobe Acrobat Reader to view


    Order On-Line


    Join our mailing list to keep informed of new products and sales!
    Enter your email address below, then click the 'Join Now' button:
    Enter Email:

    Core Cut | Diamond Products | Felker | Husqvarna | ICS | IMER | MK Diamond
    Ned-Kut | Partner | Pro-Cut | Q.E.P. | Target

    Security & Privacy    |    Contact Us at 1-800-593-6095    |    © Copyright 2002-2009 Masonry-Saw.com